Technical articles, application guides and engineering insights covering industrial water treatment, reverse osmosis, ultrapure water, EDI, water reuse and desalination.
Explore technical guides, application knowledge and engineering considerations for industrial water treatment projects.
Water ReuseOctober 27, 20268 min readStable oil-in-water emulsions can resist the gravity separation expected for free oil. Chemical demulsification should therefore be selected through representative trials and linked to the equipment that removes the destabilized material. Industrial buyers need to evaluate clarified water, recovered oil and sludge together when comparing complete treatment offers.
Read Article
Pure WaterOctober 27, 20268 min readIron-based arsenic adsorption should be selected from the actual source-water chemistry and arsenic species. Media volume alone cannot establish service life. Industrial procurement needs representative breakthrough evidence, pretreatment reliability, sampling that protects the release decision and an approved route for spent media and wash water.
Read ArticleWater ReuseOctober 27, 20268 min readPeracetic acid can be considered for a defined industrial reuse disinfection duty where its performance and receiving-stream compatibility are demonstrated. Selection requires more than a nominal oxidant dose. Review the actual formulation, microbial objective, contact arrangement, residual method and the response to changing water quality before ordering storage and feed equipment.
Read ArticleWater ReuseOctober 27, 20268 min readBreakpoint chlorination is a chemical ammonia-treatment decision that requires a measured demand curve and clear downstream limits. Industrial buyers should evaluate ammonia removal, chlorine species, competing demand and residual handling together. A generic chlorine-to-ammonia ratio is insufficient to specify the complete installed polishing package.
Read ArticleWater ReuseOctober 27, 20268 min readStruvite recovery targets a specific crystalline solid rather than undifferentiated phosphorus sludge. Industrial side-stream selection needs dissolved nutrient data, competing-ion review and trials that distinguish precipitation from recoverable crystal production. Procurement should also define what happens to residual liquid, fines and material that fails the intended product requirement.
Read ArticleWater ReuseOctober 27, 20268 min readBiogas from anaerobic industrial wastewater treatment may need hydrogen sulfide control before its intended use. A biological desulfurization package combines gas absorption with a separate liquid regeneration process. Procurement should follow the gas, liquid and sulfur boundaries through to accepted destinations rather than stopping at an outlet gas concentration.
Read ArticleWater ReuseOctober 27, 20268 min readA rotary vacuum drum filter forms cake as its filtering surface moves through a slurry and subsequent operating zones. Choosing a workable discharge method is as important as specifying filtration area. Industrial buyers should connect slurry trials to drum speed, vacuum distribution, media cleaning and the complete filtrate-handling arrangement.
Read ArticleWater ReuseOctober 27, 20268 min readA paddle dryer removes water thermally after sludge dewatering. Its duty must be expressed as water evaporation and final solids handling, not feed volume alone. Industrial selection also depends on sludge behaviour during drying, the available heat source and a complete vapour, condensate and noncondensable-gas treatment boundary.
Read ArticleWater ReuseOctober 27, 20268 min readA belt filter press combines gravity drainage with progressive mechanical dewatering between belts. Industrial procurement should connect sludge conditioning to wedge loading, belt behaviour and wash-water supply. The useful capacity is the duty achieved with the actual sludge and complete operating arrangement, including filtrate and cake destinations.
Read ArticleWater ReuseOctober 27, 20268 min readAn aeration blower inlet filter forms part of the air-supply operating boundary. Selecting an element by connection size alone leaves important questions about pressure loss, ambient contamination and service access unresolved. Review the intake as an assembly that must protect the blower while remaining within its approved operating limits.
Read ArticleWater ReuseOctober 27, 20268 min readAeration airflow comparisons are useful only when their units, reference conditions and measurement locations are clear. Thermal meters also respond to heat transfer from the gas around the sensor. Industrial buyers should review moisture, gas composition, installation and data validity alongside the nominal measuring range.
Read Article
Engineering & ProcurementOctober 27, 20268 min readA clamp-on ultrasonic survey can add flow observations without introducing a wetted meter. Its usefulness depends on pipe information, acoustic coupling and the installed flow profile. A defensible industrial survey states the conditions and uncertainty behind each result instead of treating a stable display as proof of accuracy.
Read ArticleShare the feed-water analysis, target quality and required capacity with our engineering team.
