ARTICLE CATEGORY

Industrial Water Reuse Guides

Resources for planning industrial recovery and reuse routes around wastewater characteristics, recovery and downstream water requirements.

ARTICLES

Water Reuse articles.

BHP industrial wastewater treatment equipment

Water ReuseOctober 27, 20268 min read

Chemical Demulsification of Industrial Oily Wastewater: Jar Trials and Downstream Separation

Stable oil-in-water emulsions can resist the gravity separation expected for free oil. Chemical demulsification should therefore be selected through representative trials and linked to the equipment that removes the destabilized material. Industrial buyers need to evaluate clarified water, recovered oil and sludge together when comparing complete treatment offers.

Read Article

Water ReuseOctober 27, 20268 min read

Peracetic Acid Disinfection of Industrial Reuse Water: Residual Method and Contact-Time Trials

Peracetic acid can be considered for a defined industrial reuse disinfection duty where its performance and receiving-stream compatibility are demonstrated. Selection requires more than a nominal oxidant dose. Review the actual formulation, microbial objective, contact arrangement, residual method and the response to changing water quality before ordering storage and feed equipment.

Read Article

Water ReuseOctober 27, 20268 min read

Breakpoint Chlorination for Industrial Ammonia Polishing: Demand Curves and Residual Control

Breakpoint chlorination is a chemical ammonia-treatment decision that requires a measured demand curve and clear downstream limits. Industrial buyers should evaluate ammonia removal, chlorine species, competing demand and residual handling together. A generic chlorine-to-ammonia ratio is insufficient to specify the complete installed polishing package.

Read Article

Water ReuseOctober 27, 20268 min read

Struvite Recovery from Industrial Side Streams: Supersaturation, Crystal Retention and Product Quality

Struvite recovery targets a specific crystalline solid rather than undifferentiated phosphorus sludge. Industrial side-stream selection needs dissolved nutrient data, competing-ion review and trials that distinguish precipitation from recoverable crystal production. Procurement should also define what happens to residual liquid, fines and material that fails the intended product requirement.

Read Article

Water ReuseOctober 27, 20268 min read

Biological Biogas Desulfurization After Anaerobic Wastewater Treatment: Absorber and Sulfur Balance

Biogas from anaerobic industrial wastewater treatment may need hydrogen sulfide control before its intended use. A biological desulfurization package combines gas absorption with a separate liquid regeneration process. Procurement should follow the gas, liquid and sulfur boundaries through to accepted destinations rather than stopping at an outlet gas concentration.

Read Article

Water ReuseOctober 27, 20268 min read

Rotary Vacuum Drum Filters for Industrial Slurry: Cake Formation and Discharge Selection

A rotary vacuum drum filter forms cake as its filtering surface moves through a slurry and subsequent operating zones. Choosing a workable discharge method is as important as specifying filtration area. Industrial buyers should connect slurry trials to drum speed, vacuum distribution, media cleaning and the complete filtrate-handling arrangement.

Read Article

Water ReuseOctober 27, 20268 min read

Paddle Dryers for Industrial Sludge: Evaporation Duty, Sticky Phase and Vapour Handling

A paddle dryer removes water thermally after sludge dewatering. Its duty must be expressed as water evaporation and final solids handling, not feed volume alone. Industrial selection also depends on sludge behaviour during drying, the available heat source and a complete vapour, condensate and noncondensable-gas treatment boundary.

Read Article

Water ReuseOctober 27, 20268 min read

Belt Filter Presses for Industrial Sludge: Wedge Loading, Belt Tracking and Wash Water

A belt filter press combines gravity drainage with progressive mechanical dewatering between belts. Industrial procurement should connect sludge conditioning to wedge loading, belt behaviour and wash-water supply. The useful capacity is the duty achieved with the actual sludge and complete operating arrangement, including filtrate and cake destinations.

Read Article

Water ReuseOctober 27, 20268 min read

Aeration Blower Inlet Filters: Restriction, Weather Protection and Element Sealing

An aeration blower inlet filter forms part of the air-supply operating boundary. Selecting an element by connection size alone leaves important questions about pressure loss, ambient contamination and service access unresolved. Review the intake as an assembly that must protect the blower while remaining within its approved operating limits.

Read Article

Water ReuseOctober 27, 20268 min read

Thermal Mass Airflow Meters for Wastewater Aeration: Moisture and Reference Conditions

Aeration airflow comparisons are useful only when their units, reference conditions and measurement locations are clear. Thermal meters also respond to heat transfer from the gas around the sensor. Industrial buyers should review moisture, gas composition, installation and data validity alongside the nominal measuring range.

Read Article

Water ReuseOctober 27, 20268 min read

Membrane Ammonia Recovery from Industrial Wastewater: Acid Receiver and Wetting Trials

Membrane ammonia recovery transfers free ammonia across a membrane into a reactive receiving solution. Industrial buyers need a validated feed envelope, compatible module construction and a complete receiving-stream balance before comparing package offers. This guide connects those decisions to pilot trials, controls and acceptance.

Read Article

Water ReuseOctober 26, 20268 min read

Biological Selenium Removal for Industrial Wastewater: Selenium species, Competing acceptors and solids capture

Selecting industrial wastewater biological selenium removal requires a defined operating envelope and evidence relevant to the installed duty. This procurement guide addresses selenium species, competing acceptors and solids capture, with practical boundaries for trials, interfaces, maintenance and acceptance before an industrial buyer commits to the package.

Read Article